Our available training dates for 2025
Basic technical training
June 30 – July 4, 2025
September 22 – 26, 2025
December 1 – 5, 2025
About the Upcoming Training
Due to the limited training facilities and to enable the participants to benefit more from the training,
maximum 10 participants are recommended (first come first serve basis).
Dates
The following training dates are available
Basic Technical Training
March 17 – 21, 2025
June 30 – July 4, 2025
September 22 – 26, 2025
December 1 – 5, 2025
Venue
2nd Floor Training Room
SWAN Analytische Instrumente AG
Studbachstrasse 13
8340 Hinwil/ Switzerland
Agenda and Topics
The complete program can be found here.
Cost
The training is free of charge, lunches are included.
The participants bear the cost of travelling/ transportation and accommodation.
Language
The basic training will be conducted in English.
Targeted Audience
Service/support technicians who have been working with Swan instruments but never been trained, newcomers and sales people who would like to know more about Swan products.
Initial Agenda and Topics of Basic Technical Training
Initial Agenda
| 09:00 | Meet and Greet, Swan Company presentation, Swan Support presentation |
| 10:30 | Coffee Break |
| 10:40 | Electronics |
| 12:00 | Lunch Break |
| 13:00 | Potentiometry– Presentation |
| 15:00 | Coffee Break |
| 15:10 | Potentiometry- Hands on Session |
| 16:30 | End |
| 09:00 | Factory Tour, SAC – Presentation |
| 10:15 | Coffee Break |
| 10:30 | SAC- Hands on Session |
| 12:00 | Lunch Break |
| 13:00 | Conductivity – Presentation |
| 15:00 | Coffee Break |
| 15:10 | Conductivity – Hands on Session |
| 16:30 | End |
| 09:00 | TOC– Presentation |
| 10:15 | Coffee Break |
| 10:30 | TOC – Hands on Session |
| 12:00 | Lunch Break |
| 13:00 | Photometry – Presentation |
| 15:00 | Coffee Break |
| 15:10 | Photometry – Hands on Session |
| 16:30 | End |
| 09:00 | Amperometry – Presentation and Hands on Session |
| 10:15 | Coffee Break |
| 10:30 | Turbidity – Presentation and Hands on Session |
| 12:00 | Lunch Break |
| 13:00 | Disinfection- Presentation |
| 14:30 | Coffee Break |
| 14:45 | Disinfection- Hands on Session |
| 16:30 | End |
| 09:00 | Question Time |
| 09:30 | Final Test |
| 10:30 | Coffee Break |
| 10:40 | Feedback form & Greetings |
| 12:00 | End |
Topics
For each parameter and instrument mentioned below, presentation will include respectively:
- Measuring principle
- Description of instruments
- Maintenance & Troubleshooting
- AMI/AMU Transmitter
- AMI II/ AMU II Transmitter
- Communication Option
- Troubleshooting on transmitter
- Microcon replacement and FW upload (USB and Swan Terminal)
- AMI pH/Redox: electrode installation
- AMI pH/Redox: standard calibration
- AMI Sodium: sensors installation
- AMI Sodium: sensor etching
- AMI Sodium: sensor calibration
- AMI Soditrace: service programming
- AMI Soditrace: valve block test
- AMI Soditrace: solenoid valve maintenance
- AMI SAC254: Startup procedure
- AMI SAC254: Verification
- AMI SAC254: General maintenance
- AMI Deltacon Power: Set of cell constant
- AMI Deltacon Power: Check of temperature compensation
- AMI Deltacon Power: Opening and closing slot-lock
- AMI Deltacon Power: Replace resin
- AMI Deltacon DG: Activation of degasser
- AMI CACE: Replace Service Kit
- AMI II CACE DG: Activation of degasser and replace service kit
- AMI Solicon4: Standard Calibration
- AMI Silica: Standard calibration/Grab Sample
- AMI Silica: Perform verification
- AMI Silica/Silitrace: Reagent preparation
- AMI Silitrace: Reaction coil replacement
- AMI Silica/Silitrace/Sequencer: 6 way valve replacement
- AMI Line TOC: General maintenance (tubing, lamp, and filter replacement)
- AMI Turbitrack: Performing Verification
- AMI Turbiwell: Performing Verification
- Chematest 42: Perform turbidity verification
- AMI Oxytrace: Sensor cap replacement
- AMI Oxytrace: Sensor calibration
- AMI Oxytrace: Zero Verification
- AMI Oxytrace QED: Faraday Verification
- AMI Codes II (CC TC): Clean photometer
- AMI Codes II (CC TC): Exchange pumping frame
- AMI Codes II (CC TC): Prepare reagents
- AMI Codes II (CC TC): Performing verification
- AMI Codes II (CC TC): Process Calibration (with CT30)
- AMI Trides: Process Calibration (with CT30)